Audi 100

1982-1990 of release

Repair and car operation




Audi 100
+ 1.1. Governing bodies and devices
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. Exhaust system
+ 6. Power supply system
+ 7. Transmission
+ 8. Running gear
+ 9. Steering
- 10. Brake system
   10.1. Technical characteristics
   10.2. Adjustment of provision of a pedal of a brake
   10.3. Main cylinder of a brake
   10.4. Brake mechanism of a forward wheel of the Teves brand
   10.5. Brake mechanism of a forward wheel of the GIRLING brand
   10.6. Brake disk
   10.7. Case of a bracket and piston
   10.8. Drum-type brake mechanism of a back wheel
   10.9. Brake drum
   10.10. Wheel brake cylinder
   10.11. Disk brake mechanism of a back wheel
   10.12. Pressure regulator
   + 10.13. Parking brake
   10.14. Anti-blocking system of brakes (ABS)
   10.15. Pumping of brake system
+ 11. Body
+ 12. Electric equipment


работа в Москве



10.10. Wheel brake cylinder

GENERAL INFORMATION

Wheel brake cylinder

1–protective cap;
2–piston;
3–cuff;
4–protective cap;
5–valve of production of air;
6–bolt;
7–case;
8–spring

Replacement

PERFORMANCE ORDER
1. To remove a brake drum (see subsection 8.2.3).
2. To turn on from a reverse side of a brake board (see fig. The drum-type brake mechanism of a back wheel) a nut of fastening of a tube and to disconnect a tube from the union of the wheel brake cylinder. To muffle a tube opening.
3. To unscrew two bolts of fastening of the wheel cylinder.
4. To dissolve slightly top ends of brake shoes by means of two screw-drivers and to remove the wheel brake cylinder.
5. To establish the brake wheel cylinder on a brake board, having slightly dissolved the top ends of brake shoes by means of two screw-drivers. Thus to watch, that ledges at end faces of pistons were сориентированы outside and a flat surface adjoined to socks of brake shoes.
6. To connect a brake tube, having greased previously its end with brake liquid, and to tighten a nut of fastening the moment of 15-20 N · m (1,5–2,0 kgfs · м).
7. To establish a brake drum and a wheel.
8. After installation it is necessary to pump over the repaired brake mechanism (see subsection 10.15).
9. To squeeze out against the stop a brake pedal for self-regulation of the brake mechanism.

Dismantling, defektovka of details and assembly

To replace defective details of the wheel cylinder it is possible without removing it from the car.

PERFORMANCE ORDER
1. To remove brake shoes (see subsection 10.8) if the cylinder does not act in film from the car.
2. To pick up carefully a screw-driver and to remove protective caps (see fig. The wheel brake cylinder) from both parties of the cylinder.
3. To take out from the cylinder case pistons with cuffs and a spring.
4. To wash out details of the wheel brake cylinder pure brake liquid and to dry.
5. The mirror of the cylinder should not have рисок, sinks and the corrosion centers. In the presence of these defects it is necessary to replace the cylinder. On carving parts of the cylinder there should not be mechanical damages.
6. Cuffs of the wheel cylinder should be elastic and elastic. The fragmentary, inflated and hardened cuffs, and also risks having on working surfaces, it is necessary to replace. Protective caps also should be elastic and elastic. It is obligatory to replace the fragmentary, inflated and hardened caps in order to avoid dirt and water hit in the wheel cylinder.
7. The surfaces of pistons contacting to a mirror of the cylinder, should not have traces of unilateral wear. Otherwise it is recommended to replace the wheel cylinder assembled.
8. The carving of a tip of a brake tube should not have mechanical damages. On the union of a tip there should not be cracks and traces of visible deformation.
9. To weaken an inhaling of the valve of production of air.
10. To establish on the cuff piston. Working edges of cuffs should be directed in the cylinder. To grease pistons with cuffs brake liquid and an internal surface of the cylinder fresh brake liquid.
11. To insert into the cylinder the piston on the left side.
12. To establish a protective cap. It should be put on hardly a head of the piston and a seat on the case.
13. To insert on the right side into the cylinder a spring and to unscrew the valve of production of air. Then to insert the second piston and to establish a protective cap.
14. To wrap the valve of production of air.
15. To establish brake shoes, a brake drum and a wheel.
16. After installation it is necessary to pump over the repaired brake mechanism (see subsection 10.15).
17. To squeeze out against the stop a brake pedal for self-regulation of the brake mechanism.