Audi 100

1982-1990 of release

Repair and car operation




Audi 100
+ 1.1. Governing bodies and devices
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. Exhaust system
+ 6. Power supply system
+ 7. Transmission
+ 8. Running gear
+ 9. Steering
- 10. Brake system
   10.1. Technical characteristics
   10.2. Adjustment of provision of a pedal of a brake
   10.3. Main cylinder of a brake
   10.4. Brake mechanism of a forward wheel of the Teves brand
   10.5. Brake mechanism of a forward wheel of the GIRLING brand
   10.6. Brake disk
   10.7. Case of a bracket and piston
   10.8. Drum-type brake mechanism of a back wheel
   10.9. Brake drum
   10.10. Wheel brake cylinder
   10.11. Disk brake mechanism of a back wheel
   10.12. Pressure regulator
   + 10.13. Parking brake
   10.14. Anti-blocking system of brakes (ABS)
   10.15. Pumping of brake system
+ 11. Body
+ 12. Electric equipment


работа в Москве



10.5. Brake mechanism of a forward wheel of the GIRLING brand

GENERAL INFORMATION

Brake mechanism of a forward wheel of the GIRLING brand

1–a block with wires of the sensor of wear of brake shoes;
2–bolt;
3–bracket case;
4–a directing finger;
5–bolt;

6–bracket basis;
7–brake shoes;
8–heatinsulating laying;
9–rotary fist;
10-brake board;
11-brake disk

Replacement of brake shoes

PERFORMANCE ORDER
1. To establish the car on the parking brake.
2. To establish basic whetstones under back wheels.
3. To weaken bolts of fastening of a forward wheel.
4. To raise and establish on support a forward part of the car.
5. To remove a wheel, having unscrewed finally fastening bolts.
6. To wash out the brake mechanism warm water and to dry. Application for cleaning of brakes of gasoline, diesel fuel or any other mineral solvents is inadmissible.
7. To check wear of brake shoes through an opening in the bracket case. If the thickness of frictional overlays of blocks at least makes on the one hand less than 2 mm, it is necessary to replace sets of blocks from both parties of the car.
8. To disconnect a block with wires from the sensor of wear of brake shoes.
9. To unscrew the bottom bolt of fastening of the case of a bracket, holding thus directing finger with a key.
10. To turn the bracket case down round an axis of the top finger. To mark brake shoes if old blocks as replacement of internal and external blocks among themselves, and also between left and right wheels is inadmissible are established again. It can lead to non-uniform braking. To remove brake shoes.
11. To clear of dirt and a rust of a detail of a brake, especially seats of brake shoes. Application for cleaning of brakes of gasoline, diesel fuel or any other mineral solvents is inadmissible.
12. If new brake shoes are established, it is necessary to press the piston into the cylinder accurately. Thus to watch, that the piston did not warp.
13. To check correctness of installation of heatinsulating laying.
14. To establish on the bracket basis brake shoes, watching that press springs stood vertically up and parallel to the upper edge of brake shoes. Old blocks to establish according to earlier made marking.
15. To lower the bracket case.
16. To wrap the top bolt of fastening the moment of 35 N · m (3,5 kgfs · м), holding thus directing finger with a key.
17. To connect a block with wires to the sensor of wear of blocks.
18. To establish a forward wheel and наживить fastening bolts.
19. To lower the car on the earth and to tighten bolts of fastening of a wheel evenly on a diagonal the moment of 110 N · m (11,0 kgfs · м).
20. To press several times a brake pedal for piston installation into position.
21. To check level of brake liquid in a tank and if necessary to add.