Audi 100

1982-1990 of release

Repair and car operation

Audi 100
+ 1.1. Governing bodies and devices
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. Exhaust system
+ 6. Power supply system
+ 7. Transmission
+ 8. Running gear
+ 9. Steering
- 10. Brake system
   10.1. Technical characteristics
   10.2. Adjustment of provision of a pedal of a brake
   10.3. Main cylinder of a brake
   10.4. Brake mechanism of a forward wheel of the Teves brand
   10.5. Brake mechanism of a forward wheel of the GIRLING brand
   10.6. Brake disk
   10.7. Case of a bracket and piston
   10.8. Drum-type brake mechanism of a back wheel
   10.9. Brake drum
   10.10. Wheel brake cylinder
   10.11. Disk brake mechanism of a back wheel
   10.12. Pressure regulator
   + 10.13. Parking brake
   10.14. Anti-blocking system of brakes (ABS)
   10.15. Pumping of brake system
+ 11. Body
+ 12. Electric equipment

работа в Москве

10.7. Case of a bracket and piston


Brake bracket of Teves firm

1–bracket basis;
2–protective cover;
4–sealing ring;
5–bracket case;
6–rubber plug;
7–plastic plug;
8–a directing finger;
9–antisplash cap;
10-protective cap;
11-valve of production of air

1. To establish the car on the parking brake.
2. To establish basic whetstones under back wheels.
3. To weaken an inhaling of bolts of fastening of a forward wheel.
4. To raise and establish on support a forward part of the car.
5. To remove a wheel.
6. To unscrew a fastening nut, to separate brake hoses and to muffle an opening of the brake hose which has remained on the car.
7. To unscrew two directing fingers (see fig. A brake bracket of Teves firm), having removed previously antisplash caps, and to remove the bracket case.


1. To remove a protective cover (see fig. Brake bracket of Teves firm) piston. To clamp the bracket case in a vice with overlays of sponges from soft metal. To take out the piston from the cylinder, having submitted the compressed air via the union for a brake hose and holding the piston with a hand or having enclosed a wooden level.
2. To take out a sealing ring from the cylinder, using a wooden shovel. Application of metal subjects is not recommended, as it can lead to damage of a pro-point of the cylinder under a sealing ring.
3. To unscrew the pumping valve.
4. To wash out the piston and the cylinder fresh brake liquid.

Survey and defektovka of details of the case of a bracket

1. To examine a working surface of the piston and the cylinder. At existence on working surfaces of the piston and the cylinder of wear tracks, corrosion, sinks and забоин to replace the bracket case complete with the piston.
2. The sealing ring and a protective cap of the piston are subject to obligatory replacement.


1. To grease an internal surface of the cylinder with fresh brake liquid.
2. To grease a new sealing ring with fresh brake liquid and to insert into a cylinder pro-point.
3. To grease a new protective cover with fresh brake liquid and to insert it into a pro-point on the piston.
4. To insert the piston into the cylinder effort of fingers, without applying any tools, and by means of a screw-driver accurately to insert an external edge of a protective cover into a cylinder pro-point.
5. To grease the valve of pumping with fresh brake liquid and to screw it in the bracket case.


The bracket case as it should be, the return is established to removal. Thus to wrap two directing fingers the moment of 25 N · m (2,5 kgfs · м), holding thus directing finger with a key. After installation to pump over the brake which has undergone to repair (see subsection 10.15).