Audi 100

1982-1990 of release

Repair and car operation




Audi 100
+ 1.1. Governing bodies and devices
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. Exhaust system
+ 6. Power supply system
+ 7. Transmission
+ 8. Running gear
+ 9. Steering
- 10. Brake system
   10.1. Technical characteristics
   10.2. Adjustment of provision of a pedal of a brake
   10.3. Main cylinder of a brake
   10.4. Brake mechanism of a forward wheel of the Teves brand
   10.5. Brake mechanism of a forward wheel of the GIRLING brand
   10.6. Brake disk
   10.7. Case of a bracket and piston
   10.8. Drum-type brake mechanism of a back wheel
   10.9. Brake drum
   10.10. Wheel brake cylinder
   10.11. Disk brake mechanism of a back wheel
   10.12. Pressure regulator
   + 10.13. Parking brake
   10.14. Anti-blocking system of brakes (ABS)
   10.15. Pumping of brake system
+ 11. Body
+ 12. Electric equipment


работа в Москве



10.8. Drum-type brake mechanism of a back wheel

GENERAL INFORMATION

Drum-type brake mechanism of a back wheel

1–cup;
2–clamping spring;
3–driving lever;
4–brake shoe;
5–top coupling spring;
6–rasporny level;
7–adjusting wedge;
8–wheel brake cylinder;
9–brake board;
10-bolt;
11-core;
12-clown;
13-press spring;
14-bottom coupling spring;
15-clamping spring of a rasporny level

Replacement of brake shoes

The thickness of frictional overlays of brake shoes should be not less than 2 mm. It is necessary to replace brake shoes in a set on both back brake mechanisms.

PERFORMANCE ORDER
1. To establish basic whetstones under forward wheels.
2. To weaken an inhaling of bolts of fastening of a back wheel.
3. To raise and establish on support a back part of the car.
4. To remove a wheel.
5. To check position of the lever of the parking brake which should be in extreme bottom situation.
6. To remove a brake drum (see subsection 8.2.3).
7. To press a cup (see fig. The drum-type brake mechanism of a back wheel) a clamping spring and, having turned it on 90 ° to remove together with a clamping spring, holding thus a cup core from a reverse side of a brake board. Similarly to remove a spring and cups from other block.
8. To disconnect the bottom coupling spring from blocks.
9. To deduce the bottom socks of blocks from the bottom emphasis and to remove brake shoes, having deduced their top socks from grooves of pistons of the wheel cylinder.
10. To disconnect a tip of a cable of a drive of the parking brake from the driving lever.
11. To clamp the bottom ends of blocks in a vice.
12. To disconnect a press spring of an adjusting wedge.
13. To disconnect the top coupling spring.
14. To disconnect a clamping spring of a rasporny level and to remove a rasporny level.
15. To clear all details of the brake mechanism.
16. To connect a clamping spring to a new forward block and a rasporny level. Then, overcoming effort of a spring, to insert the end of a rasporny level into a groove of a back block and to establish an adjusting wedge, сориентировав its ledge towards a brake board.
17. To insert other end of a rasporny level into a groove of a forward block and to establish the top coupling spring.
18. To connect a tip of a cable of a drive of the parking brake to the driving lever.
19. To insert the top socks of blocks into grooves of pistons of the wheel cylinder.
20. To establish the bottom coupling spring and to insert the bottom socks of blocks into the bottom support.
21. To establish a press spring of an adjusting wedge.
22. To establish on cup cores with clamping springs and to fix, having turned them on 90 ° and holding thus cores from the interior of a brake board.
23. To establish a brake drum.
24. To establish a wheel.
25. After the completion of work several times vigorously to press a brake pedal for installation of demanded gaps between blocks and a working surface of drums.
Prevention

If on details of the brake mechanism lubricant is found, it is necessary to replace an epiploon of the bearing of a semi-axis.