Audi 100

1982-1990 of release

Repair and car operation




Audi 100
+ 1.1. Governing bodies and devices
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. Exhaust system
+ 6. Power supply system
+ 7. Transmission
+ 8. Running gear
+ 9. Steering
+ 10. Brake system
- 11. Body
   11.1. Removal and installation of the forward buffer
   11.2. Removal and installation of facing of a radiator
   11.3. Removal and cowl installation
   11.4. Adjustment of a cable of the lock of a cowl
   11.5. Replacement локаря
   11.6. Forward wing
   11.7. Molding replacement
   11.8. Replacement of a sealant of glass of a door
   11.9. A door upholstery (release cars till December, 1987)
   11.10. Replacement of glass of a door and window regulator
   11.11. Removal and door installation
   11.12. External handle of a door
   11.13. Door lock
   11.14. Adjustment of the lock of a door
   11.15. Removal and window regulator installation with the electric drive
   11.16. Removal and installation of an external rear-view mirror
   11.17. Replacement of a reflecting element of an external rear-view mirror
   11.18. Repair of a tokoobogrevatelny element of back glass
   11.19. Removal and installation of the back buffer
   11.20. Removal and installation of a cover of a luggage compartment
   11.21. Removal and installation of the lock of a cover of a luggage compartment
   11.22. Replacement of a back decorative slip with a niche under registration plate
   11.23. Removal and installation of the central console
   11.24. Cleaning of drains (on the models equipped with the hatch)
   11.25. Removal and heater installation
+ 12. Electric equipment


работа в Москве



11.10. Replacement of glass of a door and window regulator

GENERAL INFORMATION

Fastening of the internal panel of a door

1–door frame;

2–internal panel;

3–cable of the handle of the lock;

4–bolt

Window regulator details

1–glass;

2–window regulator;

And – a site of a prileganiye of glass

Adjustment flew down

1–adjusting screw;

2–directing a window regulator

PERFORMANCE ORDER
1. To remove a door upholstery (see subsection 11.9).
2. To take out from the holder draft of the internal handle of the lock of a door and to disconnect it from the handle.
3. To unscrew four bolts of fastening of the internal panel of the door, located on corners. Thus it should be noted thickness and the provision of compensatory elements for each bolt. The bolt of forward top fastening is under a rubber sealant of an external rear-view mirror.
4. To remove the internal panel of a door assembled up.
5. For this purpose to remove from a directing core a rasporny ring, to take out a plastic washer and rubber laying. To lower and take out door glass.
6. In case of need to remove a window regulator. To remove it it is similar to window regulator removal with the electric drive (see subsection 11.15).
7. To insert glass from below and to fix a glass holder on a finger ползуна a window regulator a lock ring, having established previously rubber laying and a washer.
8. Temporarily to establish the handle of a window regulator and to lower glass down to an emphasis.
9. To expose the lower part directing a window regulator so that the finger (1) glass was in the middle of directing glasses.
10. To lift glass up against the stop.
11. To expose the lower part directing a window regulator so that glass adjoined to a sealant on all perimeter of a window and especially in a zone A.
12. If glass not densely adjoins or deforms a sealant, it is necessary to adjust the screw the provision of glass.
13. To establish from above the internal panel on a door, watching that draft of blocking of the lock was included into an opening, and to fix it on corners four bolts, having established thus the corresponding compensatory elements.
14. To connect a cable of the internal handle of the lock to the lever and to fix it in the holder.
15. To establish an internal upholstery of a door.