Audi 100

1982-1990 of release

Repair and car operation




Audi 100
+ 1.1. Governing bodies and devices
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. Exhaust system
+ 6. Power supply system
+ 7. Transmission
+ 8. Running gear
+ 9. Steering
+ 10. Brake system
- 11. Body
   11.1. Removal and installation of the forward buffer
   11.2. Removal and installation of facing of a radiator
   11.3. Removal and cowl installation
   11.4. Adjustment of a cable of the lock of a cowl
   11.5. Replacement локаря
   11.6. Forward wing
   11.7. Molding replacement
   11.8. Replacement of a sealant of glass of a door
   11.9. A door upholstery (release cars till December, 1987)
   11.10. Replacement of glass of a door and window regulator
   11.11. Removal and door installation
   11.12. External handle of a door
   11.13. Door lock
   11.14. Adjustment of the lock of a door
   11.15. Removal and window regulator installation with the electric drive
   11.16. Removal and installation of an external rear-view mirror
   11.17. Replacement of a reflecting element of an external rear-view mirror
   11.18. Repair of a tokoobogrevatelny element of back glass
   11.19. Removal and installation of the back buffer
   11.20. Removal and installation of a cover of a luggage compartment
   11.21. Removal and installation of the lock of a cover of a luggage compartment
   11.22. Replacement of a back decorative slip with a niche under registration plate
   11.23. Removal and installation of the central console
   11.24. Cleaning of drains (on the models equipped with the hatch)
   11.25. Removal and heater installation
+ 12. Electric equipment


работа в Москве



11.12. External handle of a door

GENERAL INFORMATION

External handle of the lock of a door

1,2-rotary brackets;
3–handle;
4–screw;
5–lock ring;
6–driving lever;
7–spring;
8–casing;
9–sealing ring;
10-lock cylinder;
11-casing;
12-laying;
13-lock cylinder

Installation of a rotary bracket

1–deepening in the lock handle;

2–bracket;

And, In – the provision of a bracket at installation

Removal

PERFORMANCE ORDER
Release models till December, 1987.
1. To pick up a screw-driver a forward part of a decorative overlay of the handle and to remove it.
2. To turn out the screw of fastening of the handle, located under a slip.
3. To open a door and to take out the rubber cap located around the lock.
4. To turn out two screws of fastening of the handle.
5. To extend carefully on itself the handle from a door, having deduced a hook in a forward part from a door opening.
6. To disconnect drafts from the handle, having raised by means of a screw-driver the holder, and to remove the external handle of a door.
Release models since December, 1987.
7. To disconnect from the handle draft of blocking of the lock and executive draft.
8. To remove brackets, having turned them on 65 °.
9. To turn out the screw and to remove the handle.

Dismantling (removal of the cylinder of the switch of the lock)

PERFORMANCE ORDER
1. To insert a key into the lock switch.
2. To turn out the screw of fastening and to take out the clown of the cylinder of the switch of the lock with a spring.
3. To take out the cylinder of the switch of the lock with a key.
4. To wind the cylinder with an insulating tape and only after that to take out from it a key. Otherwise of the cylinder will drop out сувалды.

Assembly

PERFORMANCE ORDER
1. To insert the cylinder of the switch of the lock into the handle.
2. To establish a spring (1). For this purpose to compress it and to put on one its end a ledge (2).
3. To establish the clown on a tetrahedron against the stop. Thus to watch, that the ledge was between the spring ends.
4. To screw the fastening screw.

Installation

PERFORMANCE ORDER
Release models till December, 1987.
1. To insert a hook on a forward part of the handle into an opening of a door and to connect to the draft handle by means of a screw-driver. Thus a tip of direct draft to put on a metal spherical finger, and a tip of the bent draft – on a plastic spherical finger. To fix drafts holders.
2. To insert finally external handle into a door with laying.
3. To screw screws of fastening of the handle.
4. To establish a rubber cap.
5. To establish a decorative slip.
6. To check operation of the handle. The lock should open easily and reliably be locked.
Release models since December, 1987.
7. To establish the handle upside-down removals.
8. Thus to establish a bracket in situation B, and then to turn it in situation A.
9. Deepening in the handle should enter into gearing with a bracket. The ends of a spring (1) should be in the compressed condition at the left and to the right of the driving lever (2).