Audi 100

1982-1990 of release

Repair and car operation




Audi 100
+ 1.1. Governing bodies and devices
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. Exhaust system
+ 6. Power supply system
+ 7. Transmission
+ 8. Running gear
+ 9. Steering
+ 10. Brake system
- 11. Body
   11.1. Removal and installation of the forward buffer
   11.2. Removal and installation of facing of a radiator
   11.3. Removal and cowl installation
   11.4. Adjustment of a cable of the lock of a cowl
   11.5. Replacement локаря
   11.6. Forward wing
   11.7. Molding replacement
   11.8. Replacement of a sealant of glass of a door
   11.9. A door upholstery (release cars till December, 1987)
   11.10. Replacement of glass of a door and window regulator
   11.11. Removal and door installation
   11.12. External handle of a door
   11.13. Door lock
   11.14. Adjustment of the lock of a door
   11.15. Removal and window regulator installation with the electric drive
   11.16. Removal and installation of an external rear-view mirror
   11.17. Replacement of a reflecting element of an external rear-view mirror
   11.18. Repair of a tokoobogrevatelny element of back glass
   11.19. Removal and installation of the back buffer
   11.20. Removal and installation of a cover of a luggage compartment
   11.21. Removal and installation of the lock of a cover of a luggage compartment
   11.22. Replacement of a back decorative slip with a niche under registration plate
   11.23. Removal and installation of the central console
   11.24. Cleaning of drains (on the models equipped with the hatch)
   11.25. Removal and heater installation
+ 12. Electric equipment


работа в Москве



11.6. Forward wing

GENERAL INFORMATION

Bottom back fastening of a forward wing

1, 2 – the screw;

3–washer

Top fastening of a forward wing

1–bolt;

2–forward wing

Removal

PERFORMANCE ORDER
1. To remove the forward buffer (see subsection 11.1) and локарь (see subsection 11.5).
2. To remove a forward overlay of a wing.
3. To remove the turn index (see subsection 12.1.5.6).
4. To disconnect lateral fastening of the bottom spoiler so that to get access to screws (1, 2).
5. To turn out screws of fastening of a wing.
6. To turn out the screw (1) fastening of a wing.
7. To open a door and to turn out the screw (1) fastening of the wing, located over a door loop.
8. To turn out from below a wing two screws.
9. Through a niche of a wheel to turn out the screw of fastening of an arm to a forward rack.
10. To open a cowl and to unscrew bolts of the top fastening of a wing.
11. To remove a wing from the car.

Installation

PERFORMANCE ORDER
1. To clear surfaces on a wing and a body in places of their connection.
2. To put in wing junctions with a body a hermetic layer.
3. To establish a wing and to wrap bolts of its top fastening.
4. To screw other screws of fastening of a wing. Thus to watch the correct installation of washers.
5. To screw the screw (1).
6. To screw the screw (1), having opened a door.
7. To establish into place the bottom spoiler.
8. To establish the turn index.
9. To establish локарь and the forward buffer.
10. To establish a wheel and наживить bolts of its fastening.
11. To lower the car on the earth and finally to tighten bolts of fastening of a wheel evenly on diameter the moment of 110 N · m (11,0 kgfs · м).