Audi 100

1982-1990 of release

Repair and car operation




Audi 100
- 1.1. Governing bodies and devices
   + 1.1.1. Release models till January of 1988 g
   + 1.1.2. Release models since January of 1988 g
   1.2. Window regulators with the electric drive
   1.3. An external rear-view mirror with the electric drive
   1.4. Internal rear-view mirror
   1.5. Cowl
   1.6. Forward seats with mechanical adjustment
   1.7. Forward seats with the electric drive
   1.8. Transportation of lengthy subjects
   + 1.9. Engine start
   1.10. Precautionary measures at an engine stop
   1.11. Cruise control
   1.12. Heating and ventilation
   1.13. Control panel conditioner
   1.14. Board computer
   1.15. Management of the board computer on release models till January, 1988.
   1.16. Blocking of the internal handle of the lock of a back door
   1.17. Car running in
   1.18. Car check before departure
   1.19. Replacement of operational liquids and lubricants
   + 1.20. Servicing of cars of release till August, 1985.
   + 1.21. Servicing of cars of release since August, 1985.
   1.22. Periodicity of greasing of knots of the car
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. Exhaust system
+ 6. Power supply system
+ 7. Transmission
+ 8. Running gear
+ 9. Steering
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment


работа в Москве



1.17. Car running in

GENERAL INFORMATION

In a running in (the first 1500 km of operation) occurs intensive extra earnings of details of the car. Therefore how the car during this period is maintained, reliability, durability and profitability of the car will depend substantially. A running in there should pass the new car, and also the car on which the engine was replaced or capitally repaired.

In a running in it is necessary to adhere to the following rules:

 – to begin movement only on the first transfer; to avoid movement on high speeds and with the maximum frequency of rotation of a cranked shaft. For this purpose it is necessary to include in due time the transfer corresponding to speed of movement; whenever possible to avoid movement in heavy road conditions (on deep snow, sand, dirt etc.);
 – periodically to check and if necessary to regulate a tension of belts of a drive of auxiliary units (the generator, the pump of the hydraulic booster of a steering, etc.).

It is necessary to remember that in a running in belts are most intensively stretched; to watch a condition and if necessary to tighten all fixing elements of the car. The special attention needs to be turned on fastening of wheels, details of a steering, forward and back suspension brackets and a reception pipe of the exhaust silencer to a final collector of the engine.

After run of 1000 km it is necessary:

 – to check and if necessary to adjust gaps in a drive of valves on models with engines without hydropushers of valves;
 – to check and if necessary to adjust frequency of rotation of a cranked shaft idling both the contents WITH and SN in the fulfilled gases; to replace the oil filter and oil in the engine.

After run of 1500 km it is necessary:

 – to check and if necessary to tighten all available carving connections. Thus special attention to turn on fastenings of the generator, a pulley of the generator, a starter, a reception pipe of the exhaust silencer, a radiator, support of the engine, a drive of coupling, a drive of brakes, transmissions, a case of coupling, wheels, details of a suspension bracket, a steering;
 – to check and if necessary to adjust a tension of belts of a drive of auxiliary units, frequency of rotation of a cranked shaft idling both the contents WITH and SN in the fulfilled gases;
 – to check a pretightness of bearings of naves of lobbies and back wheels, a regulator of pressure of back brakes, a convergence of forward wheels.