Audi 100

1982-1990 of release

Repair and car operation




Audi 100
+ 1.1. Governing bodies and devices
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. Exhaust system
+ 6. Power supply system
- 7. Transmission
   + 7.1. Coupling
   + 7.2. Mechanical drive of switching off of coupling
   + 7.3. Hydraulic drive
   + 7.4. Transmission
   - 7.5. Drive of forward wheels
      7.5.1. Semi-axis
      7.5.2. Internal hinge of equal angular speeds (CV JOINT)
      7.5.3. External hinge of equal angular speeds (CV JOINT)
+ 8. Running gear
+ 9. Steering
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment


работа в Москве



7.5. Drive of forward wheels

7.5.1. Semi-axis

GENERAL INFORMATION

Drive of a forward wheel

1–nut;
2–semi-axis;
3–lock plate;
4–bolt;
5–washer;
6–cover

Model
Length of a semi-axis
the right
the left
With 4-cylinder engines:
  – from mechanical KP
579,20
540,70
  – from automatic KP
540,70
590,50
With 5-cylinder engines:
  – from mechanical KP
550,90
550,90
  – from automatic KP
529,10
582,80

Removal

PERFORMANCE ORDER
1. To brake the car the parking brake and to establish an emphasis under back wheels.
2. To weaken an inhaling of bolts of fastening of a forward wheel and to unscrew a nut of 1 fastening of a semi-axis.
3. To raise and establish on a support a forward part of the car.
4. Finally to unscrew bolts of fastening and to remove a forward wheel.
5. On models with an automatic transmission to remove holders of pillows of the stabilizer of cross-section stability and to disconnect the stabilizer from a rotary fist.
6. To unscrew bolts of 4 fastenings of the internal CV JOINT to a flange of a semi-axis and to take out them with lock plates 3.
7. To shift a semi-axis up, having disconnected it from a semi-axis flange.
8. To turn a steering wheel against the stop to the left at dismantle of the left semi-axis or to the right at dismantle of the right semi-axis.
9. Выпрессовать from a wheel nave a shlitsevy part of a semi-axis by means of a stripper and to remove a semi-axis from the car.

Installation

PERFORMANCE ORDER
1. To clear of dirt and the remains of special glue of a shlitsa of a nave and a semi-axis and to wipe them gasoline.
2. To put special D6 glue on a shlitsa of a semi-axis (only on release models till January, 1988 and on models with an automatic box) on length of 5-6 mm from an end face of a shlitsevy part. After that the trial trip can be made only through 60 mines let's to glue harden.
3. To insert a semi-axis into a wheel nave.
4. To connect a semi-axis to a flange and to wrap bolts of fastening М10 with lock plates the moment of 80 N · m (8,0 kgfs · м) or М8 – the moment of 45 N · m (4,5 kgfs · м).
5. On models with an automatic transmission to connect the stabilizer of cross-section stability.
6. To establish a wheel and наживить fastening bolts.
7. Наживить a new nut of fastening of a nave (on release models after January, 1988 – a special bolt).
8. To lower the car on wheels.
9. To tighten a nut the moment of 280 N · m (28,0 kgfs · м). On release models after January, 1988 to tighten a special bolt the moment of 200 N · m (20,0 kgfs · м), and then to tighten on a turn quarter (90 °).
10. To tighten bolts of fastening of a wheel evenly the moment of 110 N · m (11,0 kgfs · м).