Audi 100

1982-1990 of release

Repair and car operation




Audi 100
+ 1.1. Governing bodies and devices
+ 2. Technical characteristics
+ 3. Engines
+ 4. Cooling system
+ 5. Exhaust system
+ 6. Power supply system
+ 7. Transmission
+ 8. Running gear
- 9. Steering
   9.1. Technical characteristics
   9.2. Steering wheel
   + 9.3. Steering column
   9.4. Steering mechanism
   9.5. Adjustment of the mechanism of a steering
   9.6. Steering draft
   9.7. Pump of the hydraulic booster of a steering
   9.8. Check of pressure of forcing of the pump of the hydraulic booster of a steering
   9.9. Pumping of system of the hydraulic booster of a steering
   9.10. Driving belt of the pump of the hydraulic booster
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment


работа в Москве



9.4. Steering mechanism

GENERAL INFORMATION

Steering mechanism

1–bolt;
2–case of the mechanism of a steering;
3–collar;
4–protective cover;
5–arm;
6–adjusting screw;
7–bottom shaft of a column of a steering;
8–collar;
9–cover;

10-a tip with the spherical hinge;
11-carving coupling;
12-lock-nut;
13-left steering draft;
14, 15 – bolts;
16-clamping plate;
17-damper;
18-right steering draft

The steering mechanism with the hydraulic booster

1–a bringing bolt;
2–case of the mechanism of a steering;
3–tube;
4–protective cover;
5–tank;
6–a taking-away hose;
7–bottom shaft of a column of a steering;
8–laying;
9–bolt;
10-shaft of a driving gear wheel of the mechanism of a steering;
11-antisplash casing;
12-valve case;

13-cover;
14-adjusting bolt;
15-a tip with the spherical hinge;
16-a bringing hose;
17-lock-nut;
18-left steering draft;
19-arm;
20, 21 – bolts;
22-clamping plate;
23-right steering draft;
24-collar;
25-carving coupling

Removal

PERFORMANCE ORDER
1. To brake the car the parking brake and to establish an emphasis under back wheels.
2. To remove a tank of a stekloomyvatel and to put it aside, without disconnecting a hose.
3. To raise and establish on a support a forward part of the car.
4. To unscrew a bolt of fastening and to disconnect a steering damper from an arm (a steering without the hydraulic booster).
5. To unscrew bolts of fastening of steering bent for to a lath of the steering mechanism.
6. To take away drafts from the steering mechanism, having removed an arm and a clamping plate.
7. To unscrew a bolt of fastening of a coupling collar of the bottom shaft of the helmsman of a column, to shift a collar up and to disconnect the bottom shaft from a shaft of a driving gear wheel of the mechanism of a steering.
8. To remove a sealant of a shaft of a steering column, having taken out it from an opening in a front board.
9. To merge liquid from a tank and to disconnect bringing and taking-away hoses from the valve case (a steering with the hydraulic booster).
10. To unscrew fastening bolts from both parties and to remove the steering mechanism from the car, having deduced it through a niche of the right wheel.

Installation

PERFORMANCE ORDER
1. To establish the steering mechanism upside-down.
2. To connect steering drafts (see subsection 9.6), a clamping plate to replace with the new.
3. Finally a bolt of fastening of a collar to tighten the moment of 25 N · m (2,5 kgfs · м) after gap adjustment between a casing of a steering wheel and a casing of podrulevy switches (see subsection 9.2). The left bolts of fastening of a case of the mechanism of a steering to tighten the moment of 20 N · m (2,0 kgfs · м), and right – the moment of 25 N · m (2,5 kgfs · м).
4. On models with the hydraulic booster of a steering the submitting bolt of hoses is tightened by the moment of 40 N · m (4,0 kgfs · м).
5. After installation of the steering mechanism to check and if necessary to adjust a convergence of forward wheels at service station. On models with the hydraulic booster of a steering to pump over system.